E46 series BMW 3

since 1998 of release

Repair and car operation


E46 series BMW 3
+ BMW 3 Cars (E46)
- Current leaving and service
   Introduction
   Current leaving
   General information on control
   Check of levels of liquids
   Check of a condition of tires and pressure in them. Designation of tires and disks of wheels
   Replacement of impellent oil and oil filter
   Replacement of a filtering element of the air filter
   Checks of brake system
   Replacement of an element of the filter of air of salon
   Check of a condition of driving ridge belts
   Check of a condition and replacement of hoses of an impellent compartment
   Check of functioning of system of cooling and frost resistance of cooling liquid
   Check of a condition of system of production of the fulfilled gases
   Check of level of oil in a manual box of gear shifting
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts
   Check of level of liquid of system of hydrostrengthening of a wheel
   Visual check of a body and its bottom
   Check of seat belts
   Rotation and replacement of wheels
   Condition check, replacement of brushes and adjustment of a corner of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of brake liquid
   Check and replacement of spark plugs
   Check of fuel system, replacement of the fuel filter. Operation of diesel model in the conditions of winter
   Greasing of loops and locks of doors
   Replacement of a battery of a key of remote control
+ Engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ engine Electric equipment
+ RKPP and transmission line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes

2b332cca

Rotation and replacement of wheels

1 Rotation can be carried out at emergence of signs of non-uniform wear of protectors. However remember that in case of successful rotation of all four wheels you eventually should replace all tires at the same time.
As carrying out this procedure demands a car raising over the earth and removals of wheels, check at the same time and operation of brake mechanisms (address to the Section of Check of brake system).

Even if you are not going to make rotation, at least check reliability of an inhaling of bolts of fastening of wheels.


2 At faster wear of forward tires it is recommended to interchange the position lobbies and back tires. Thus, service life of all four tires is equalized.
3 Address to information in Poddomkrachivaniye's Section and towage for the correct raising of the car at wheel replacement.
4 Car should be lifted on the lift or to establish it on support that all four wheels were lifted over the earth. Make sure that the car is reliably fixed!

Do not replace separately any tire. Both tires of one bridge are necessary to replace. Tires with bigger depth of a protector are established on back wheels. Lobbies and back wheels should have tires of the identical size and type, and at all-wheel drive cars also one manufacturer and one execution of a protector. The tires which have worked more than 6 years, it is necessary to apply only in case of failure, thus it is necessary to be careful when driving. At replacement and removal of tubeless tires it is necessary to change the gate surely.


5 in case of use of tires with a protector assuming movement only in the certain direction that is specified by an arrow on a lateral surface of the tire, the specified direction is necessary for observing. Only thus achievement of necessary road qualities of the car, namely absence of hydroplaning, stability on the road, low noise level and small wear is provided. If the spare wheel owing to failure has to be established with an opposite direction of rotation, such application should be only temporary since achievement specified above road qualities of the car thus is impossible. It especially belongs to movement on the wet road. Therefore it is recommended to coordinate speed of movement with conditions of the road and to reinstall the tire according to the specified direction of rotation.


Spare wheel

It is possible to establish 6 Spare wheel both on a lobby, and on a back axis.
7 Spare wheel is intended only for short-term use and it is necessary to replace it with the usual as soon as possible.
8 After installation of a spare wheel pressure in its tire should make 4.2 bar.
9 With the established spare wheel it is impossible to exceed speed of 80 km/h. It is necessary to avoid the maximum acceleration of the car, intensive braking and sharp turns.
10 At installation of a spare wheel the road gleam under the corresponding axis decreases approximately by 30 mm.

It is not necessary to apply spare wheels from cars of other types.

It is not allowed to establish two or more spare wheels.

Replacement of wheels

11 Remove a decorative cap of a wheel.
12 On the car standing on the earth, tighten the hand brake and weaken bolts of fastening of a wheel.
13 Lift the relevant party of the car and fix on supports.

14 Unscrew the top bolt of fastening of a wheel and on its place screw an adjusting pin. Use of an adjusting pin facilitates installation of a spare wheel.

Disks from easy alloys are protected from corrosion by a transparent varnish. Be careful not to damage a varnish covering. At covering damage, cover a disk with a varnish coat.


15 For an exception of "prikipaniye" of disks of wheels to a nave, before wheel installation, apply a thin film greasings on the fillet of a nave aligning a disk of a wheel.
16 Zinced wheel bolts can be applied only on capital stamped disks.
17 Disks from easy alloys fasten only the chromeplated wheel bolts on which there is a conic rotating washer. This washer established under a head of a bolt, protects a disk surface at a tightening of bolts.
18 Before a vvinchivaniye do not grease a carving of bolts of fastening of a wheel.

19 Tightening of bolts of fastening of a wheel make evenly in some stages in diagonal sequence.

The moment of a tightening of bolts of fastening of a wheel is given in Specifications.


Antisliding chains

20 Chains should be established only on forward wheels, as well all-wheel drive car.
21 Chains of antisliding can be established only on tires by dimension of 195/65 R 15. Installation of chains of antisliding on an emergency wheel for technical reasons is not allowed.
22 It is necessary to use only close-meshed chains acting no more than on 15 mm (including zamkovy links).
23 At installation of chains of antisliding it is necessary to remove full-size caps of wheels and decorative rings of disks. For safety reasons wheel bolts should be protected by special caps.
24 Before movement on free from snow it is necessary for site of a way to remove antisliding chains. They worsen road performance of the car, increase wear of tires and quickly collapse.