| Engine designation (Type)//release Beginning |
|
316i | М43TU (OHC)//9/98 |
| 318i | М43TU (OHC)//4/98 |
| 320i | М52TU (DOHC)//4/98 |
| 323i | М52TU (DOHC)//4/98 |
| 325i | М52TU (DOHC)//4/98 |
| 328i | М52TU (DOHC)//4/98 |
| 330i | M54//9/99 |
| M3 | S52 (DOHC)//-/99 |
| 320d | М47 (DOHC)//4/98 |
| 330d | M57U//-/99 |
| Working volume of cylinders, cm3 |
| 316i | 1895 |
| 318i | 1895 |
| 320i | 1991 |
| 323i | 2494 |
| 325i | 2494 |
| 328i | 2793 |
| 330i | 2979 |
| M3 | 3246 |
| 320d | 1951 |
| 330d | 2926 |
| Capacity, kW (h.p.) at rpm//the Torque, H · m at rpm |
| 316i | 77 (105)/5300//165/2500 |
| 318i | 87 (118)/5500//180/3900 |
| 320i | 110 (150)/5900//190/3500 |
| 323i | 125 (170)/5500//245/3500 |
| 325i | 141 (192)/6000//245/3500 |
| 328i | 142 (193)/5500//280/3500 |
| 330i | (231)/5900/300/3500 |
| M3 | (342)/7900/356/4900 |
| 320d | 100 (136)/4000//280/1750 |
| 330d | (184)/4000/390/1750 |
| Arrangement/number of cylinders//Number of valves on the cylinder |
|
316i | ryadnoye/4//2 |
|
318i | ryadnoye/4//2 |
|
320i | ryadnoye/6//4 |
| 323i | ryadnoye/6//4 |
| 325i | ryadnoye/6//4 |
| 328i | ryadnoye/6//4 |
| 330i | ryadnoye/6//2 |
| M3 | /6/4 4 |
| 320d | ryadnoye/4//4 |
| 330d | ryadnoye/6//4 |
| Diameter of cylinders, mm |
| 316i | 85.0 |
| 318i | 85.0 |
| 320i | 80.0 |
| 323i | 84.0 |
| 325i | 84.0 |
| 328i | 84.0 |
| 330i | 84.0 |
| M3 | 87.0 |
| 320d | 84.0 |
| 330d | 84.0 |
| The 1st repair | +0.250 |
| The 2nd repair | +0.500 |
| Course of pistons, mm |
| 316i | 83.5 |
| 318i | 83.5 |
| 320i | 66.0 |
| 323i | 75.0 |
| 325i | 75.0 |
| 328i | 84.0 |
| 330i | 89.6 |
| M3 | 91.0 |
| 320d | 88.0 |
| 330d | 88.0 |
| Extent of compression |
| 316i | 9.7 |
| 318i | 9.7 |
| 320i | 11.0 |
| 323i | 10.5 |
| 325i | 10.5 |
| 328i | 10.2 |
| 330i | 11.0 |
| M3 | 11.3 |
| 320d | 19.0 |
| 330d | 18.0 |
| Pressure of a compression, bar |
| Petrol engines |
| standard value (new) | 9-14 |
| limit of wear | 7.5 |
| Diesel engines |
| standard value (new) | 25-31 |
| limit of wear | 19.0 |
| Pistons |
| Gap in the cylinder | 0.03 |
| Wear limit | 0.06 |
| Piston rings |
| Gap in a flute, mm |
| Kompressionnoye | 0.02-0.07 |
| Maslosjemnoye | 0.02-0.06 |
| Wear limit | 0.12 |
| Gap in a lock/limit of wear, mm |
| Kompressionnoye | 0.15-0.40/0.8 |
| Maslosjemnoye | 0.25-0.50/1.0 |
| Three-componental maslosjemny | to 1.0/1.3 |
| Admissible minimum height of a head of cylinders |
| M43TU engines |
| Nominal size | 141.0 mm |
| Processing limit | 140.55 mm |
| M52TU engines |
| Nominal size | 140.0 mm |
| Processing limit | 139.70 mm |
| Cranked shaft |
| Radical bearings |
| Gap/limit of wear, mm | 0.02-0.06/0.17 |
| Maximum ovality, mm | 0.03 |
| Shatunnye bearings |
| Gap/limit of wear, mm | 0.01-0.06/0.12 |
| Axial люфт crankshaft / limit of wear, mm | 0.07-0.17/0.25 |
| Klapannye gaps | Adjustment is not required, as hydrojacks are applied |
| Greasing system | Compulsory circulating system with the shesterenchaty oil pump |
| Impellent oil |
| Type |
| Petrol engines |
| Viscosity of SAE OW-30: CASTROL Formula SLX, DEA Ultec Syn-T, ESSO Ultron (Fuel Economy), SHELL Helix Ultra, VEEDOL Syntrhon. |
| Viscosity of SAE OW-40: ARAL Super Tronic, AVIA SYNTH, BMW Super Power Spezial, BP VISCO 7000, MOBIL 1, SHELL Helix Ultra. |
| Viscosity of SAE 5W-30: AGIP TECSINT, ARAL Super Tronic, BMW Super Power Plus, CASTROL TXT, DEA Viscobil S1, FINA FE 2000 5W-30, LIQUI MOLY Profi Synthol, MOBIL 1, MOBIL 1 Rally Formula, SHELL Helix Ultra, VALVOLINE Syn Power, VEEDOL Spezial R Plus. |
| Viscosity of SAE 5W-40: AGIP Extra HTS, ARAL Super Tronic, AVIA SYNTH, BMW Super Power, BP Visco 5000, DEA Viscobil S1, ELF Synthese, ESSO Megatron, FINA First, FINA Motortronic RS, LIQUI MOLY Synthoil High Tech, MOBIL 1, MOBIL 1 Rally Formula, MOTUL Synergie, SHELL Helix Plus, SHELL Helix Ultra, TOTAL Activa 9000, TOTAL quartz 9000, VALVOLINE Syn Power. |
| Diesel engine 320d |
| Any impellent oils which are at the same time corresponding to norms of ACEA A3-96 and ACEA B3-96. Viscosity: The OW X-th, 5W-X and 10W-X. Here X designates any value, for example 30, 40 or 50. |
| Volume, with filter replacement |
| 316i | 4.0 |
| 318i | 4.0 |
| 320i | 6.5 |
| 323i | 6.5 |
| 328i | 6.5 |
| 320d | 5.0 |
| Difference between marks of "max" and “min” in a measuring core | 1 liter |
| Pressure in system, a bar |
| On single turns | not less than 0.5 |
| Petrol engines on 5000 rpm | 4.0-4.5 |
| Diesel engines on 4000 rpm | 3.7-4.7 |
| Reduktsionny valve |
| Pressure of opening, bar | 4.0 |
| Cooling system | Circulating, with the water pump, the thermostat, the fan and a lamellar and tubular radiator |
| Volume of cooling liquid |
| 316i | 6.0 |
| 318i | 6.0 |
| 320i | 8.4 |
| 323i | 8.4 |
| 328i | 8.4 |
| 320d | 7.0 |
| Air filter | Dry, with a paper element |
| Ridge maple belts |
| 318i | 6 РК x 1733 (5 РК x 950) |
| 320d | 5 РК x 2030 (5 РК x 836) |
| 320i, 323i, 328i | 6 РК x 1538 (5 РК x 863) |
| Fuel |
| 316i | unleaded, AI 95 is not worse |
| 318i | unleaded, AI 95 is not worse |
| 320i | unleaded, AI 983) is not worse |
| 323i | unleaded, AI 983) is not worse |
| 325i | unleaded, AI 98 is not worse |
| 328i | unleaded, AI 983) is not worse |
| 330i | unleaded, AI 983) is not worse |
| M3 | unleaded, AI 983) is not worse |
| 320d | The diesel |
| 330d | The diesel |
| 3) Filling by AI 95 gasoline with insignificant decrease in engine capacity is possible. AI 91 can be applied only in exceptional cases. |
| Control system двигателем1) |
| 316i | BMS 46 |
| 318i | BMS 46 |
| 320i | Siemens MS 42.0 |
| 323i | Siemens MS 42.0 |
| 325i | Siemens MS 42.0 |
| 328i | Siemens MS 42.0 |
| 320d | DDE Bosch 3.0 |
| 330d | DDE Bosch 3.0 |
| 1) BMS - a control system of the BMW engine. MS - a control system of the engine (Motronic). DDE - a digital control system of the diesel engine |
| System of anti-blocking of brakes of ABS dynamic system of stabilization of stability built in ABS - DSC3, on the early E46 models antiprobuksovochny system - (Teves ABS/ASC Mark20ET) |
| System of ensuring additional safety of SRS | MRS2, MRS3 |
| AT with electronic control of EGS/AGS | A5S 360R Siemens AGS 20 |
| Efforts of a tightening of carving connections |
The moments of an inhaling of fixture are given also in the text of Head and on some иллюстрациях*.
*vydelenny in the text a bold print the moments of an inhaling are subject to exact observance; the efforts not allocated with a bold print are given only roughly |
| Bolts of a head of the block of cylinders |
| M43TU engines |
| 1st reception | 30 H · m |
| 2nd reception | 90 ° |
| 3rd reception | 90 ° |
| M52TU engines |
| 1st reception | 40 H · m |
| 2nd reception | 90 ° |
| 3rd reception | 90 ° |
| M47 engines |
| 1st reception | 80 H · m |
| 2nd reception | 180 ° |
| 3rd reception | 50 H · m |
| 4th reception | 90 ° |
| 5th reception | 90 ° |
| Pulling up of bolts of fastening of a head of cylinders on the warm engine, at carrying out service or repair is not allowed. |
| Bolts of fastening of the lower part of the inlet pipeline to a head of cylinders |
| М6 | 10 H · m |
| М7 | 15 H · m |
| М8 | 22 H · m |
| Support of the engine and arm |
| Bolt М8 | 22 H · m |
| Bolt М10 | 47 H · m |
| Masloslivny stopper |
| М12 (on a turn-key basis 17 mm) | 25 H · m |
| М22 | 60 H · m |
| Carving stopper of blocking of a natyazhitel of a chain (320d) | 30 H · m |
| *) Replace a sealing ring |
| Asterisks to camshafts (320d) | 20 H · m + 35 ° |
| Bolts of fastening of a flywheel to a cranked shaft |
| 316i, 318i | 120 H · m |
| 320i, 323i, 328i, 320d | 105 H · m |
| Bolts of fastening of a flange of a check point |
| М8 | 22 H · m |
| М10 | 45 H · m |
| М12 | 70 H · m |
| Sensor of pressure of oil | 35 H · m |
| Spark plugs | 25 H · m |
